|
|
We do not offer returns on this item. You are however covered by the Paypal Protection Plan by making payment with Paypal. |
If you have a Tektronix/Xerox Phaser 8200, 850, 840 printer, you can add oil to your old maintenance roller (please see link at bottom). Then, with our counter refurbishing kit you can reset the counter to 45,000 copies, then just replace the maintenance roller later and/or replace the oil as necessary. It is important to know that the when you purchase our counter that you are responsible for replacing the oil in the roller, the roller was not meant to be run dry hence why it normally needs to be replaced if oil is not added back manually. We sell the, do it yourself kit for $20.41 and it takes less than one minute to refurbish the old counter (see installation instructions below). Directions to Install Your Recharged Maintenance CounterStep 1:The Maintenance Counter is found in the maintenance drawer as show below remove this tray and press the ears while lifting up to release the plastic counter from the tray. Step 2:Using a jewelers flathead or small flathead screwdriver release the plastic latch so that the back cover is released. You will be able to see how to open the latch by looking inward to the pins on the opposite side while moving the screwdriver. Push the flat end of the hook downwards while simultaneously pulling open the back cover. Step 3:Open the cover by bending at the plastic hinge until the cover is displaced and the spent circuit board is displayed. Step 4:Remove the old circuit board by pulling outward as shown below. Properly dispose of used circuit board. Step 5:Replace with the purchased recharged counter circuit board. Step 6:Close the cover until latched again. Insert back into maintenance tray. Then insert maintenance tray into Phaser printer. You now have 45,000 copies reported to the CPU, it is very important to monitor the quality of prints to know when to replace the roller. If you see previous ghost images or the paper starts to jam then you should not print anymore until replacing the entire maintenance roller. We hope you enjoy the product. >>Simple instructions to refurbish your expired counter. Please click here<< Although you might find this cheaper on the Internet for $19.99, with us you get full service Ebay peace of mind. We are proud to be Ebay members and of our positive feedback. >>Often our customers ask if there is a way to add new oil back to their old roller. I've used the following method with good results and offer advice for free, use the info with your own discretion and liability. Please click here to learn how to add oil back to your old roller<< ---------------------------------------------- Optional Rebate Program: Send us your old green board and we will refund $2.00 per unit to your PayPal account. We are not responsible to give rebate for items lost or damaged in the mail. We recommend that you send your old board using the same enclosure box you bought the recharge kit from us in. Also if you would enclose a note giving your PayPal email to where you'd like us to refund the rebate to. If you have any questions please feel free to contact us. |
Search Information: |
|
Original Xerox 161932 Extended Capacity Maintenance Kit (016193200) to fit the Xerox Phaser 8200 Printer | |
Recharge Reset Kit For Tektronix Xerox Phaser 840 850 860 8200 Printer |
Search Information: |
|
If you have a Tektronix/Xerox Phaser Xerox 8200 860 850 840 016-1933-00 Maintenance Kit printer, you can add oil to your old Xerox 8200 860 850 840 016-1933-00 Maintenance Kit maintenance roller (please see link at bottom). Then, with our Xerox 8200 860 850 840 016-1933-00 Maintenance Kit counter refurbishing kit you can reset the Xerox 8200 860 850 840 016-1933-00 Maintenance Kit counter to 45,000 copies, then just replace the Xerox 8200 860 850 840 016-1933-00 Maintenance Kit maintenance roller later and/or replace the oil as necessary. It is important to know that the when you purchase our Xerox 8200 860 850 840 016-1933-00 Maintenance Kit counter that you are responsible for replacing the oil in the roller, the roller was not meant to be run dry hence why it normally needs to be replaced if oil is not added back manually. We sell the, do it yourself Xerox 8200 860 850 840 016-1933-00 Maintenance Kit kit for $20.41 and it takes less than one minute to refurbish the old counter (see installation instructions below).